Here is the process I used to cook a "hot & fast" barbequed beef brisket. Brisket is generally more than a little initimidating for those that have never cooked one. I know that was the case for me back in the day.

For those uninitiated, the brisket is a very tough cut found on the chest of the animal, between and behind the front legs (foreshank). Cattle walk a lot, so the front legs get a good workout. After one look at a brisket you will see that it looks like a cow's odometer. It's long and hard, like the third grade.

Tough "lesser cuts" are generally what barbeque is all about. A tough cut usually equates to a tough (long and slow) cook, but that need not be the case. This brisket was my first attempt at cooking hot and fast. The results have me scratching my head wondering why I've been torturing myself with 16-hour cooks (low & slow means about 1 - 1 ½ hours per pound).

When shopping for a brisket, you want a "whole packer". This is really two cuts in one. The pointy thicker end is called the "point" (or "deckle") and the long flat portion is called, you guessed it, the "flat".

Look for a packer in the 13-16 pound range with a flat that is fairly consistent in thickness, and with a nice white fat cap. The white fat indicates that the animal was finished on grain instead of grass. You should also check to make sure that it's flexible. As a general rule, the more flexible it is in the bag, the more tender it will be in the end. I drape mine over my forearm and look for a nice bend.

For a little different twist, you can marinate the brisket in a double batch of Patio Daddio Bovine Bath then drain and use the slather and seasoning process in step 5 below.

As always, click the image to see a larger version.

Ingredients
1 whole Packer brisket (13-16 lbs)
1/4 cup Prepared mustard (I use French's)
2/3 cup of your favorite BBQ seasoning

Method

Hot & Fast BBQ Beef Brisket

Remove the brisket from the cryovac bag, rinse well with cold water and pat dry. Put it on the cutting board fat-side-up on a double layer of paper towels. This brisket was 15 ½ pounds in the bag. I like to use a 6-inch flexible boning knife for trimming. You'll see why as we progress through the process.

Hot & Fast BBQ Beef Brisket

The first order of business in trimming is to shave the fat layer down to a reasonable thickness. Seasoning and smoke can't penetrate fat. However, it will act as an insulation layer to protect the meat when we cook it. I try to get it to about ¼-inch, but you can see it's an inexact science.

Hot & Fast BBQ Beef Brisket

Flip the brisket over and you'll notice two pockets or "kernels" of hard fat. These separate the flat and point muscles. Fat equals flavor and tenderness, but we don't need it all. Cut about ¾ of the fat out of the smaller kernel where you see the knife point.

Hot & Fast BBQ Beef Brisket

Turn the brisket around and repeat the same trimming process for the large kernel. I like to make a long horizontal cut through the fat then make two long deep angular cuts from each outside edge toward the first cut. You can see this where the knife is pointing. I was a little over-aggressive in my trimming.

Hot & Fast BBQ Beef Brisket

You can see from the pile of trimmings in the background of the picture above that I removed about 1 ½ pounds. In my experience, that's pretty typical. Now we need to smear a thin layer of mustard on all of the outer surfaces (edges too) and inside each fat kernel pocket. This will help the seasoning adhere.

Hot & Fast BBQ Beef Brisket

Season the entire surface and fat kernel pockets liberally with your seasoning. You don't need to rub it into the meat, but I pat it when I'm done to make sure it all sticks. Put the brisket on parchment paper in a large a sheet pan, cover with plastic wrap, and refrigerate overnight, or at least several hours.

Hot & Fast BBQ Beef Brisket

Start your fire and prepare for indirect cooking at medium-high heat. I recommend a mixture of cherry and hickory chunks or chips for smoke. Cook fat-side-down at 325-350º until the thickest part of the flat reaches 190º. Mine (about 14 pounds trimmed) took 5 hours at an average of 350º.

Hot & Fast BBQ Beef Brisket

At 190º we're ready to apply the finishing glaze. I use a mixture of ½ cup golden brown sugar, ½ cup beef broth, ¼ cup ketchup, 1 Tbsp Worcestershire, and 1 tsp black pepper. Spoon and spread this (with the back of the spoon) on all sides and dust with the BBQ seasoning. Cook 30 more minutes and repeat.

Hot & Fast BBQ Beef Brisket

Continue cooking until the thickest part of the flat reaches 200º. Remove from the cooker, wrap in a double layer of heavy-duty foil and let rest 30 minutes (or longer wrapped in towels). Unwrap, separate the flat and point (it's easy), slice across the grain about ¼" thick, serve and enjoy.

Notes:
The entire cook took exactly 6 hours in my homemade drum cooker (UDS), but your mileage may (and almost certainly will) vary.

I used the new Kingsford Competition Briquets for this cook. It's the first time that I've had a chance to use them.
2 Comments:
Anonymous Anonymous said...
Does 200.F get the meat as broken down as it needs to be for competition?

I have read where people are suggesting 210... What are your thoughts?
Blogger John Dawson said...
200-205* works fine for me. -John

Post a Comment

Latest posts >>

 
Free Delivery!

Subscribe via RSS or e-mail



E-mail:

Delivered by FeedBurner